#CISCO IOS TFTP SERVER SOFTWARE#

Step through the questions, answering defaults until you can change the console baud rate. Some of this output might vary from yours, depending on the router model that you are using. The output that follows was taken from a 1720 router.

#CISCO IOS TFTP SERVER SOFTWARE#

Restoring the Cisco IOS Software from ROM Monitor Mode Using Xmodem Iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii (via) FastEthernet 0/0): iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii Restoring/Upgrading the Cisco IOS Software from a TFTP ServerД®rasing the flash file system will remove all filesД®rasing device eeeeeeeeeeeeeeeeee.erased Llllllllllllllllllllllllllllllllllllllllllllll The destination filename is the same as the source filename, so just press f Enter]. Source filename ? c2600-js-l_121-3.binДЄddress or name of remote host ? 192.168.119.20Дestination filename ?

NOTE: You can also use the preceding sequence for a copy tftp startup-config command sequence.Д«acking Up the Cisco IOS Software to a TFTP Server Restoring Configurations from a TFTP ServerД¬opies the configuration file from the TFTP server to DRAM.Д®nter the name of the file you want to retrieve.Дestination filename ? В®Entsrl NOTE: You can also use the preceding sequence for a copy startup-config tftp command sequence. The name to use for the file saved on the TFTP server.Д®ach bang symbol (!) = 1 datagram of data. Saves the running configuration from DRAM to NVRAM (locally).Д¬opies the running configuration to the remote TFTP server.ДЄddress or name of remote host? 192.168.119.20Дestination Filename ?В®Entsr| Instead of entering in an EXEC-level copy command and then having the system prompt you for more information, you can enter a single command on one line with all necessary information.Д¬opy system:running-config nvram:startup-configД«acking Up Configurations to a TFTP ServerДenver#copy running-config startup-config The Cisco IFS minimizes the required prompting for many commands. NOTE: The Cisco IOS File System (IFS) provides a single interface to all the file systems available on a routing device, including the flash memory file system network file systems such as TFTP, Remote Copy Protocol (RCP), and File Transfer Protocol (FTP) and any other endpoint for reading and writing data, such as NVRAM, or the running configuration. If you want to go to a TFTP server first, make sure that the boot system tftp command is the first one you enter. If you enter boot system flash first, that is the first place the router will go to look for the Cisco IOS Software. The router will execute commands in their order on the next reload. Saves the running configuration to NVRAM. Router#copy running-config startup-config Loads the Cisco IOS Software with image-name from a TFTP server. Router(config)#boot system tftp image-name 172.16.10.3 Loads the Cisco IOS Software with image-name. Router(config)# boot system flash imagename Restoring the Cisco IOS Software using the ROM Monitor environmental variables and tftpdnld command.Restoring the Cisco IOS Software from ROM Monitor mode using Xmodem.Restoring/upgrading the Cisco IOS Software from a TFTP server.Backing up the Cisco IOS Software to a TFTP server.Restoring configurations from a TFTP server.Backing up configurations to a TFTP server.This seemed to work OK, the only problem was that I kept having to hit - it didn't seem to understand that each line was a command to be executed, and i couldn't see a way of piping in a as part of the TCL script.ДЄt least it saved a lot of laborious typing and made sure that all my routers had identical sets of files on them, which was the original objective.This chapter provides information and commands concerning the following topics: I then TFTP'd this to the router and then from the router ran it under a TCL shell: In essence, I created a script called bulkcopy.tcl which contained lines similar to the following:Д®xec copy t ftp:/ / 10.0.0.2/ vlan.dat flash://vlan.datД®xec copy t ftp:/ / 10.0.0.2/ mypackage.pkg flash://mypackage.pkgД®xec copy t ftp:/ / 10.0.0.2/ securedesktop.pkg flash://securedesktop.pkgД®xec copy t ftp:/ / 10.0.0.2/ 128MB.sdf flash://128MB.sdfД®xec copy t ftp:/ / 10.0.0.2/ home.tar flash://home.tarД®xec copy t ftp:/ / 10.0.0.2/ home.shtml flash://home.shtmlД®xec copy t ftp:/ / 10.0.0.2/ common.tar flash://common.tarДЎ0.0.0.2 is the IP address of my TFTP server.

I ended up running a TCL script, which wasn't ideal, but it took a lot of the leg work out of copying multiple files to multiple routers.

Cisco ios tftp server